HP Smart Array E200i Controller with optional battery-backed
write cache (standard BTO models)
3.
Small form factor (SFF) hot-plug drive bays (standard BTO
models)
7.
Two Mezzanine slots
4.
Local I/O connector
8.
Internal USB Connector (standard BTO models)
At
A Glance
This document covers the HP ProLiant BL460c server blade
only. For more information on HP BladeSystems c-Class Infrastructure and
HP BladeSystem c-Class Interconnect Components, please see the following
QuickSpecs:
The HP ProLiant BL460c provides greater 2P x86 server blade density without
compromise and maximum power-efficiency with flexibility and choice.
HP ProLiant BL460c server blade includes:
Processor:
Up to two Intel® Xeon® 5400 Series processors
Up to two Intel® Xeon® 5200 Series processors
Supports up to 2 Dual-Core 3.50 GHz, 1333 MHz FSB -1X6 MB Level
2 cache memory, and up to 2 Quad-3.33 GHz 1333MHz-2x6 MB Level 2
cache memory
Intel 5000P chipset supporting up to a 1333 MHz Front Side Bus
Memory:
Up to 64 GB of memory, supported by (8) slots of PC2-5300 Fully
Buffered DIMMs at 667 MHz
NOTE: 64 GB of memory is
supported with 80W processors and below. 64 GB of memory is
not supported with 120W processors.
NOTE: Up to three 16 GB (2
x 8 GB) memory option kits or 48 GB of memory is supported with
120W processors
Supporting low-power memory
Advanced ECC memory support
Supporting memory interleaving (2x1); memory mirroring and online
spare capacity.
Storage Controller:
Integrated HP Smart Array E200i RAID controller with 64 MB cache
(with optional battery-backed write-cache with an upgrade to 128
MB cache in standard BTO models. Supports RAID 0,1 in standard BTO
models
NOTE: Drive-less model available
through CTO for customers not utilizing internal disk drives
and attaching directly to SAN. Please note that this model does
not replace any prior model offerings. The feature listed above
is not included in the standard Drive-less configure to order
model. However, all configure to order models offer optional
support for small form factor (SFF) hot-plug drive bays, HP
Smart Array E200i Controller (with optional battery-backed write
cache), and Internal USB Connector. See Factory Integrated Model
section for more information.
Internal Drive Support:
Up to 2 small form factor (SFF) SAS or SATA hot plug hard disk
drives or SATA solid state drives
NOTE: Drive-less model now
available through CTO for customers not utilizing internal disk
drives and attaching directly to SAN. Please note that this
model does not replace any prior model offerings. The feature
listed above is not included in the standard Drive-less configure
to order model. However, all configure to order models offer
optional support for small form factor (SFF) hot-plug drive
bays, HP Smart Array E200i Controller (with optional battery-backed
write cache), and Internal USB Connector. See Factory Integrated
Model section for more information.
Network Controller:
Two (2) embedded NC373i Multifunction Gigabit Server Adapters
with iSCSI boot, TCP/IP offload engine, and optional accelerated
iSCSI
One (1) additional embedded 10/100 network adapter dedicated to
iLO 2 management NOTE: The Gigabit Ethernet
adapters transmit from the server at 2000 Mbps only, full duplex
per port. For more information, see the "Network Controller"
item in Standards Features section.
Mezzanine Support:
Two (2) additional I/O expansion slots via mezzanine card.
Supports up to two (2) mezzanine cards
Dual-Port Fibre Channel Mezzanine (4-Gb) options for SAN connectivity
(Choice of Emulex or QLogic).
Wide variety of 10GbE and 1GbE network adapter options for
additional network ports
QLogic QMH4062 Gigabit Ethernet iSCSI initiator
4X DDR InfiniBand (IB) Mezzanine (20 Gb/s) options for low
latency server interconnectivity (based on Mellanox technology
I/O Accelerator mezzanine options for high transaction rate
local storage
Internal USB Support:
One (1) internal USB 2.0 connector for security key devices and
USB drive keys in standard BTO models
NOTE: Drive-less model now
available through CTO for customers not utilizing internal disk
drives and attaching directly to SAN. Please note that this
model does not replace any prior model offerings. The feature
listed above is not included in the standard Drive-less configure
to order model. However, all configure to order models offer
optional support for small form factor (SFF) hot-plug drive
bays, HP Smart Array E200i Controller (with optional battery-backed
write cache), and Internal USB Connector. See Factory Integrated
Model section for more information.
Form Factor:
HP ProLiant BL460c server blade plugs vertically into the BladeSystem
c7000 enclosure and horizontally into the BladeSystem c3000 enclosure.
Infrastructure Management:
HP ProLiant Onboard Administrator (powered by the Integrated Light-Out
2 management processor) for simplified server setup, health monitoring
and recovery, power and thermal control, and lights-out remote administration
HP Insight Control, a product option, delivers essential infrastructure
management that can help save time and money by making it easy to
deploy, migrate, monitor, control and optimize your IT infrastructure
through a single, simple management console. Insight Control supports
both Windows and Linux-based central management servers.
HP Insight Dynamics for ProLiant, a product option, is an integrated
command center that enables IT Staff personnel to continuously analyze
and optimize a converged infrastructure, while automating and reducing
the cost of common data center tasks by as much as 40 percent. This
ultimately enables them to dynamically keep pace with the organization's
changing business requirements.
HP offers three different c-Class server blade enclosures to meet
your individual needs:
The HP BladeSystem c7000 rack enclosure is 10U high and holds
up to 16 ProLiant BL460c servers plugged vertically.
The HP BladeSystem c3000 rack enclosure is 6U high and holds
up to 8 HP ProLiant BL460c servers plugged horizontally.
The HP BladeSystem c3000 tower enclosure is designed with
casters for sites without racks and holds up to 8 HP ProLiant
BL460c servers plugged vertically.
Server blades, storage blades, interconnect modules, power supplies,
fans, and redundant Onboard Administrator modules are all designed
to fit into the c3000 and c7000 enclosures.
This product is covered by a global limited warranty and supported
by HP Services and a worldwide network of HP Authorized Channel
Partners. Hardware diagnostic support and repair is available for
three years from date of purchase. Support for software and initial
setup is available for 90 days from date of purchase. Enhancements
to warranty services are available through HP Care Pack services
or customized service agreements. Certain restrictions and exclusions
apply. Hard drives have either a one year or three year warranty;
refer to the specific hard drive QuickSpecs for details. NOTE: Server warranty includes
3 year Parts, 3 year Labor, 3-year on-site support. Warranty repairs
may be accomplished through the use of Customer Self Repair (CSR)
parts. These parts fall into two categories: 1) Mandatory CSR parts
are designed for easy replacement. A travel and labor charge will
result when customers decline to replace a Mandatory CSR part; 2)
Optional CSR parts are also designed for easy replacement but may
involve added complexity. Customers may choose to have HP replace
Optional CSR parts at no charge. Additional information regarding
worldwide limited warranty and technical support is available at:
http://h18004.www1.hp.com/products/servers/platforms/warranty/index.html
NOTE: Intel
5400 and 5200 Series processors are 64-bit and support Intel VT. Intel.
5200 Series processors are dual-core; Intel 5400 series processors are quad-core. NOTE: For the Intel 5200 and 5400 Series, the letter preceding the
model number indicates the performance/wattage of the processor. "X"
denotes High Performance/Wattage; "E" denotes Enterprise Performance/Wattage
(Mainstream); and "L" denotes Lower Wattage.
Upgradeability
Upgradeable to 2 processors
Future upgradeable to Xeon® Series 5400/5300 Quad-Core processors (Please
contact your regional sales support to determine quad core upgradeability.
Some of the earlier shipping models may not support this upgrade). 5100
Dual-Core models are not upgradeable to the 5200 Dual-Core processors.
Cache
Memory
2 x 6 MB shared L2 cache
(5400 Series)
1 x
6 MB L2 cache (5200 Series)
Chipset
Intel® 5000P Chipset
Memory
Type
PC2-5300
Fully Buffered DIMMs at 667 MHz
Standard
1
GB (2 x 512 MB) 2 GB (2 x 1 GB)
Maximum
64 GB (8 x 8 GB) NOTE: Memory must be installed in
pairs. NOTE: 64GB of memory is supported with 80W processors and below.
64GB of memory is NOT supported with 120W processors. NOTE: Up to three 16GB (2 x 8 GB) of memory is supported with 120W
processors
Network
Controller
Two (2) embedded
NC373i Multifunction Gigabit Server Adapters with iSCSI boot, TCP/IP offload engine,
and optional accelerated iSCSI
One (1) additional 10/100 NIC dedicated to iLO 2 Management NOTE:
The Gigabit Ethernet adapters transmit from the server at 2000 Mbps, full duplex
per port only. However, within a Linux environment, the speed can be reduced or
"throttled" using a feature available within the Linux operating system;
see the white paper at: http://h71028.www7.hp.com/ERC/downloads/4AA1-5513ENW.pdf
for more information.
Multifunction
Networking
The embedded multifunction NC373i adapters combine standard Gigabit Ethernet
networking, TCP/IP offload engine (TOE), iSCSI boot and optional accelerated
iSCSI into a single adapter.
TOE moves the processing of data in the TCP protocol stack from the
server CPU to the network card, freeing CPU cycles for other activities.
With TOE, network communications are improved, and server efficiency
is increased. The NC373i offers TOE for Microsoft® Windows 2000
and 2003 environments.
The iSCSI network boot (iSCSI boot) allows the BL460c to boot from
a remote operating system (OS) image located on a storage area network
(SAN). The BL460c uses an iSCSI firmware image (iSCSI boot option ROM)
making the remote disk drive appear as a local, bootable C: drive. The
BL460c is configured to connect to and boot from the iSCSI target disk
on the network and download the OS image from the iSCSI target disk.
The iSCSI boot option ROM is supplied by HP at no cost. The additional
cost and mezzanine slot usage of an add-in iSCSI HBA card is not required.
Additionally, the HP iSCSI boot solution includes scripts to significantly
simplify the installation process.
Two I/O expansion mezzanine
slots (one x8 and one x4)
Integrated Manageability
HP ProLiant Onboard Administrator
(includes but not limited to functionality in Integrated Lights-Out 2 (iLO
2) Standard Blade Edition (integrated on motherboard)
Storage
Controller
HP Smart Array E200i
Controller
64 MB
memory module supports RAID 0,1 Available upgrades: 128 MB with Battery-backed
write cache
NOTE:
For customers who choose to configure a driveless model via CTO, a storage
controller is not required. See Factory Integrated Models section for more information.
Maximum Internal
Storage
Hot Plug SAS
600GB SAS
2 x 300GB Serial SCSI
Hot Plug SATA
1TB SATA
2 x 500GB Serial ATA
NOTE:
For customers who choose to configure a driveless model via CTO, internal
storage is not required. See Factory Integrated Models section for more
information.
Graphics
Integrated ATI RN-50, 32 MB
video memory
Graphics
Resolution Supported
Resolution
Color Depths
1600 x 1200, 64K, 256, 16
1280 x 1024, 16.7M, 64k, 256, 16
1024 x 768, 16.7M, 64k, 256,16
800 x 600, 16,7M, 64k, 256, 16
640 x 480, 16,7M, 64k, 256, 16 NOTE: Maximum resolution available
via ProLiant Onboard Administrator remote console is 1280 x 1024.
Fibre Channel Support
Two optional Fibre Channel HBAs are supported by the HP ProLiant BL460c.
Both mezzanine circuit boards connect directly to the server blade system
board. These Fibre Channel HBAs are available via option kits and must
be ordered separately.
Two option kits
Emulex LPe1105-HP 4Gb FC HBA for HP c-Class BladeSystem (403621-B21)
Based on the same field-proven ASIC, firmware, and driver technology
as Emulex's renowned LPe1150 HBA, the Emulex LPe1105-HP is fully driver
compatible with all Emulex HBAs
QLogic QMH2462 4Gb FC HBA for HP c-Class BladeSystem (403619-B21)
Uses common drivers which means that customers can standardize on
one QLogic driver whether they are using the QMH2462 or other 4Gb and
2Gb HBAs powered by QLogic
Emulex and QLogic Fibre Channel HBAs feature:
Optimal performance utilizing PCI Express
4/2/1Gb/s auto negotiating speeds
Dual-ports for redundant path connections
Up to two FC HBAs per server blade providing redundant FC HBA support
Optimized for HP StorageWorks and supported by third party SAN vendors
Support for Microsoft® Windows® and Linux operating systems
environments
Compatible SAN
HP ProLiant BL460c server blades are optimized for HP StorageWorks MSA,
EVA and XP
HP Virtual Connect simplifies server connectivity to LANs and SANs, and
reduces costs. Unique HP Flex-10 technology makes maximum use of 10Gb
Ethernet bandwidth by allowing multiple ports within a single Industry
Standard connection that can be dynamically tuned to meet individual server
requirements. HP Virtual Connect Enterprise Manager (VCEM) provides a
central console to administer connections and workloads for thousands
of servers. For more information on Virtual Connect Ethernet, Fibre Channel
and management options see: www.hp.com/go/virtualconnect
HP Insight management software
HP Insight Foundation
Managing the growing number of servers can be complex and expensive for
your organization. IT managers need to address changing business needs
with tools that meet the challenges of managing today's complex Datacenters.
HP provides management solutions that are designed to simplify a server's
installation, configuration and maintenance throughout the entire server
lifecycle. This provides the customer with higher levels of operational
efficiency and highly reliable systems: www.hp.com/go/foundation.
The foundation pack includes:
HP ProLiant Onboard Administrator (powered by the HP Integrated Lights-Out
2 management processor) simplifies server setup, health monitoring, power
and thermal control, and lights-out remote administration of ProLiant
ML, DL, and BL servers. HP ProLiant Onboard Administrator functions without
additional software, and can be accessed from any location via a web browser.
It works hand-in-hand with HP Systems Insight Manager, Insight Control
suites, and the Insight Dynamics-VSE suite helping customers unlock the
value of the ProLiant platform and deliver the highest possible quality
of IT service to the business.
HP Insight Control, as product option, delivers essential infrastructure
management that can help save time and money by making it easy to deploy,
migrate, monitor, remote control, and optimize your IT infrastructure
through a single, simple management console.
Two versions of Insight Control are available, to serve environments requiring
either a Linux-based or a Windows-based central management server: HP
Insight Control for Linux, and HP Insight Control. See http://www.hp.com/go/insightcontrol
HP Insight Control includes one year of 24 x 7 HP Software Technical Support
and Update Service ensuring rapid access to HP support staff and proactive
delivery of software updates. For more information about this service,
please visit: http://www.hp.com/services/insight.
HP Insight Dynamics for ProLiant
HP Insight Dynamics for ProLiant, a product
option, is an integrated command center that enables IT Staff personnel
to continuously analyze and optimize a converged infrastructure, while automating
and reducing the cost of common data center tasks by as much as 40 percent.
As a powerfully integrated by design toolkit to accelerate complex technology
projects and simplify daily operations that ultimately enable IT Staff personnel
to dynamically keep pace with the organizations changing business requirements.
It enables them to plan capacity and power continuously, balance across
physical and virtual resources, and ensure cost-effective high availability.
It also enables IT organizations to provision infrastructure consistently
and automatically from pools of shared resources using a self-service portal.
Resources provisioned can range from a single virtual machine to complex
multi-tier environments and their associated physical and virtual resource
requirements. In addition to the previous functional benefits, it also provides
a cost-effective disaster recovery for physical and virtual environments
that works with HP StorageWorks Continuous Access software for both the
Enterprise Virtual Array and the XP storage array allowing application environments
to be reactivated in minutes with the touch of a button to a remote location.
NOTE:
For more information on HP's Certified and Supported ProLiant Servers for OS and
Virtualization Software and latest listing of software drivers available for your
server, please visit our Support Matrix at: http://www.hp.com/go/supportos.
Availability
Dual-Port Fibre Channel Mezzanine Card for redundant SAN connection
Two (2) embedded Gigabit Ethernet adapters for redundant LAN connections
Two (2) hot-plug SAS/SATA drive bays and integrated RAID (HP Smart Array
E200i) controller on every BTO model server blade (Battery-backed write
cache is optional.)*
Redundant ROM on each server blade
Advanced ECC Memory - can correct a multi-bit error (up to 4 bits)
that occurs within one memory chip
* For customers who
choose to configure a driveless model via CTO, these features are not required.
See Factory Integrated Models section for more information.
Industry Standard Compliance
ACPI 2.0 Compliant
PCI 2.2 Compliant
WOL Support
Microsoft® Logo certifications
USB 2.0 Support
Security
One (1) internal USB 2.0 connector for security key devices and USB
drive keys on every BTO model server blade*
Power-on password
Administrator's password
Integrated Lights-Out 2 has 12 customizable user accounts and SSL
encryption
Integrated Lights-Out 2 can be disabled via a Global Setting
*
For customers who choose to configure a driveless model via CTO, internal USB
connectors are not available unless 447711-B21 is selected. See Factory Integrated
Models section for more information.
Factory Express Portfolio for
Servers and Storage
HP Factory Express offers configuration,
customization, integration and deployment services for HP servers and storage
products. Customers can choose how their factory solutions are built, tested,
integrated, shipped and deployed.
Factory Express offers service packages for simple configuration, racking,
installation, complex configuration and design services as well as individual
factory services, such as image loading, asset tagging, and custom packaging.
HP products supported through Factory Express include a wide array of servers
and storage: HP Integrity, HP ProLiant, HP ProLiant Server Blades, HP BladeSystem,
HP 9000 servers as well as the MSAxxxx, VA7xxx, EVA, XP, rackable tape libraries
and configurable network switches.
For more information on Factory Express services on your specific server
model please contact your sales representative or go to http://www.hp.com/go/factory-express.
HP
Enterprise Configurator
The HP eConfigure Enterprise
Configurator now provides factory default racking for our HP hardware portfolio.
This approach is aligned with our strategic direction to meet the needs
and expectations of our valued customers. If you require "custom"
rack configuration, please contact HP's Customer Business Center or an Authorized
Partner for assistance. http://www.hp.com/products/configurator NOTE: This feature is not supported
in the NEW Drive-less model which is available through CTO for those who
do not utilize internal hard disk drives and attach to SAN.
Service
and Support
HP Care Pack services provide total care and support expertise with committed
response designed to meet your IT and business needs.
The HP Care Pack service for HP ProLiant BL c-Class server blades, cover
the server blade and all HP branded hardware options qualified for the
server, purchased at the same time or afterwards, internal to the server.
To fully capitalize on your HP BladeSystem servers' capabilities requires
a service partner who thoroughly understands your server technology and
systems environment. HP Services, an industry leader in provision of multi
vender support solutions provides a range of support services designed
to meet the varying needs of business. Whether an SMB or large global
corporation HP has a HP BladeSystem server support offer to help you speedily
deploy and maximize system uptime.
Recommended Service Simplify ProLiant solution implementation,
maintenance and management.
Support Service 4-Hour Response Coverage, 3-Year, 24
x 7, Same Business Day
Deployment Service Installation and Start Up for HP
BladeSystem Infrastructure
Enhanced Service - Optimize service level to increase IT performance
and availability
Support Service HP Proactive BladeSystem Service, 1-Year
Deployment Service Enhanced Network Installation and
Start-up for HP BladeSystem Switches
Installation & Start-Up service for HP BladeSystem Infrastructure
plus HP BladeSystem Enhanced Network Installation and Start-UP as per
the Customer Description and/or Data Sheet. To be delivered on a scheduled
basis 8am-5pm, M-F, excluding HP holidays.
Configuration Information - Factory Integrated Models
NOTE:
This section lists some of the steps required to configure a Factory Integrated
Model. To ensure only valid configurations are ordered, HP recommends the
use of an HP approved configurator. Contact your local sales representative
for information on CTO product offerings and requirements. NOTE: HP does not allow factory integration of options into standard
models listed above.
Configure-to-order server blades must start with a CTO Blade. NOTE: FIO indicates that this option is a Factory Installable Option.
Step
1: Base Server Blade Configuration (Select a configurable Blade)
HP
Models
HP
ProLiant BL460c Driveless CTO Blade
447707-B21
Configurable
Model ships with:
Two (2) embedded
NC373i Multifunction Gigabit Server Adapters plus one (1) additional 10/100 NIC
dedicated to iLO 2 Management
Integrated
Lights-Out 2 Standard Blade Edition
Step
2: Choose Required Options (one of the following from each list unless otherwise
noted):
HP
Processors
For
single processor configuration choose:
Quad-Core Processor
Option Kits
Intel® Xeon®
Processor X5470 (3.33 GHz, 1333 FSB, 120 W) Option Kit, FIO NOTE:
If 2 processors are desired, select one 492308-B21 and one 492308-B21.
492308-B21
Intel® Xeon®
processor X5460 (3.16 GHz, 1333 FSB, 120 W) Option Kit, FIO Base NOTE: If 2 processors are desired, select one 459973-B21 and one 459973-B21.
459973-B21
Intel® Xeon®
processor X5450 (3.00 GHz, 1333 FSB, 120 W) Option Kit, FIO Base NOTE: If 2 processors are desired,
select one 463056-B21 and one 463056-B21.
463056-B21
Intel® Xeon®
processor E5450 (3.00 GHz, 1333 FSB, 80 W) Option Kit, FIO Base NOTE: If 2 processors
are desired, select one 459489-B21 and one 459489-B21.
459489-B21
Intel® Xeon®
processor E5440 (2.83 GHz, 1333 FSB, 80 W) Option Kit, FIO Base NOTE: If 2 processors are desired,
select one 459490-B21 and one 459490-B21.
459490-B21
Intel® Xeon®
processor E5430 (2.66 GHz, 1333 FSB, 80 W) Option Kit, FIO Base NOTE: If 2 processors are desired,
select one 459491-B21 and one 459491-B21.
459491-B21
Intel® Xeon®
Processor E5420 (2.50 GHz, 1333 FSB, 80 W) Option Kit, FIO Base NOTE: If 2 processors are desired,
select one 459492-B21 and one 459492-B21.
459492-B21
Intel® Xeon®
Processor L5420 (2.50 GHz, 1333 FSB, 50 W, LV) Option Kit, FIO Base NOTE: If 2 processors are
desired, select one 462876-B21 and one 462876-B21.
462876-B21
Intel® Xeon®
processor E5410 (2.33 GHz, 1333 FSB) Option Kit, FIO Base NOTE: If 2 processors are desired, select
one 459493-B21 and one 459493-B21.
459493-B21
Intel® Xeon®
Processor L5410 (2.33 GHz, 1333 FSB, 50 W LV), Option Kit, FIO Base NOTE: If 2 processors are
desired, select one 462877-B21 and one 462877-B21.
462877-B21
Intel® Xeon®
processor E5405 (2.00 GHz, 1333 FSB, 80 W) Option Kit, FIO Base NOTE: If 2 processors are desired,
select one 459494-B21 and one 459494-B21.
459494-B21
Dual-Core
Processor Option Kits
Intel® Xeon®
processor X5270 (3.50 GHz, 1333 FSB, 80W) NOTE:
If 2 processors are desired, select one 492309-B21 and one 492309-B21.
492309-B21
Intel® Xeon®
processor X5260 (3.33 GHz, 1333 FSB, 80 W) Option Kit, FIO Base NOTE: If 2 processors are desired, select
one 461623-B21 and one 461623-B21.
461623-B21
Intel® Xeon®
processor L5240 (3.00 GHz, 1333 FSB, 40 W, LV) Option Kit, FIO Base NOTE: If 2 processors are
desired, select one 461624-B21 and one 461624-B21
461624-B21
Intel® Xeon®
processor E5205 (1.86 GHz, 1333 FSB, 65 W) Option Kit, FIO Base NOTE: If 2 processors are desired, select
one 461625-B21and one 461625-B21.
NOTE:
Must be installed in pairs NOTE: 64GB of memory is supported with 80W processors and below.
64GB of memory is Not supported with 120W processors. NOTE: Up to three 16 GB (2 x 8 GB) memory option kits or 48 GB of
memory is supported with 120W processors.
Step
3: Choose Additional Factory Integratable Options (one of the following
from each list unless otherwise noted):
HP
Drive Cage Options
HP ProLiant BL460c
Hard Disk Drive Backplane, FIO NOTE: Includes USB connector.
447711-B21
NOTE:
The Hard Drive Backplane is required for all blades that support hard disk
drives or require the internal USB 2.0 connector for security key devices,
licensing or VMware ESX Server 3i.
HP
Storage Controllers
64 MB Cache - FIO
Only NOTE: Integrated HP Smart Array E200i
RAID controller supporting RAID 0/1 Controller cache module selection is
required for all blades that support hard disk drives. Select either the
standard 64 MB module above or the optional 128 MB module below. NOTE: This option is not required when configuring a Drive-less Model.
128 MB Battery-Backed
Cache Enabler NOTE: Supports the HP Smart Array
E200i Controller. NOTE: This option is not required when configuring a Drive-less Model.
NOTE:
For additional "Core Options" and "Additional Options",
please see the options sections below
HP Ethernet Mezzanine
Options
Gigabit Ethernet Mezzanines
HP NC325m PCI Express Quad Port
1Gb Server Adapter for c-Class BladeSystem NOTE: If the NC325m is installed
in mezzanine slot 1 of a half-height server, connectivity will be provided
on 2 of the 4 ports
416585-B21
HP NC326m PCI Express Dual Port
1Gb Server Adapter for c-Class BladeSystem
406771-B21
HP NC360m Dual Port 1GbE BL-c
Adapter
445978-B21
HP NC364m Quad Port 1GbE BL-c
Adapter NOTE: If the NC364m is installed
in mezzanine slot 1 of a half-height server, connectivity will be provided
on only 2 of the 4 ports
447883-B21
HP NC382m Dual Port 1GbE Multifunction
BL-c Adapter
453246-B21
NOTE: The Gigabit
Ethernet adapters above transmit from the server at 2000 Mbps, full duplex
per port only. For more information, see the "Network Controller"
segment in the Standards Features section.
10 Gigabit Ethernet Mezzanines
HP NC522m Dual Port 10GbE Multifunction
BL-c Adapter NOTE: The NC522m requires a minimum
of 2 GB of server memory. NOTE: The NC522m supports linking at 1000Mbps or 10000Mbps when not
connected to a Flex-10 enabled module and will link with all current 1Gb
switches at 1Gb.
467801-B21
HP BLc QLogic iSCSI Dual Port
Adapter with Virtual Connect Kit
488074-B22
HP NC532m Dual Port 10GbE BL-c
Adapter NOTE: The NC532m network adapter
card is required for each server blade connecting to a 10Gb interconnect
in bays 3-8 (HP BladeSystem c7000 Enclosure) or bays 3-4 (HP BladeSystem
c3000 Enclosure) NOTE: The NC532m requires a minimum of 2 GB of server memory NOTE: The NC532m will downspeed to 1Gb if paired with a 1Gb interconnect.
467799-B21
HP Fiber Channel Mezzanine
Options
Emulex LPe1105 FC Dual Channel
4Gb, PCI-E-to-Fibre Channel Host Bus Adapter
NOTE: Must be
installed in pairs. NOTE: 64GB of memory is supported with 80W processors
and below. 64GB of memory Not supported with 120W processors. NOTE:
Up to three 16 GB (2 x 8 GB) memory option kits or 48 GB of memory is supported
with 120W processors.
BL460c G1 Hard Drives
NOTE: The components
of a storage subsystem (e.g. the drive, the HBA/controller, firmware, and
the server backplane) should operate at the same data transfer rate or the
system bandwidth will be negotiated down to an acceptable level for all
components. NOTE: Hard drives have either a one year or three year warranty;
refer to the specific hard drive QuickSpecs for details.
SAS Hot Plug SFF (2.5-inch) Enterprise
(ENT) Drives
HP 300GB 6G SAS 10K SFF (2.5-inch)
Dual Port Enterprise 3yr Warranty Hard Drive
NOTE: SAS drives
have a 3 year warranty. NOTE: Please see QuickSpecs for Technical Specifications and additional
information: http://h18000.www1.hp.com/products/quickspecs/12244_div/12244_div.html
(Worldwide) NOTE: The hard drive options are not required when configuring a
Drive-less Model.
SATA Hot Plug SFF (2.5-inch)
Midline (MDL) Drives
HP 500GB 3G SATA 7.2K rpm SFF
(2.5-inch) Midline 1yr Warranty Hard Drive
HP Insight Control, Electronic
License, including 1 year of 24x7 Technical Support and Updates
T9074BAE
HP Insight Control, Single-Server
License including 1 year of 24x7 Technical Support and Updates
452148-B22
HP Insight Software Media Kit
NOTE: Insight Software DVD media
without licenses. Contains HP Systems Insight Manager, HP Insight Control,
HP Insight Dynamics, HP Insight Control for Microsoft System Center, and
Virtual Connect Enterprise Manager software. Uses an integrated installer
to perform quick and accurate software installation and updates.
436222-B21
NOTE: Licenses
ship without media. The Insight Control Media Kit can be ordered separately,
or can be downloaded at: http://www.hp.com/go/insightupdates.
NOTE: Electronic licenses can be used to purchase multiple licenses
with a single activation key, and are available in all countries except
China and Japan. Customers in China and Japan should order the physical
equivalent. NOTE: Customer will receive a license entitlement certificate, which
must be redeemed online or via fax in order to obtain the license activation
key(s). Includes one year of 24 x 7 HP Software Technical Support Service. NOTE: For additional license kits please see the Insight Control
QuickSpecs at: http://h18004.www1.hp.com/products/quickspecs/12631_div/12631_div.html
HP Insight Control for Linux
HP Insight Control for Linux,
1-server license, including one year of 24x7 Technical Support and Updates,
Electronic
TC213AAE
HP Insight Control for Linux,
No Media, 1-Server license, including one year of 24x7 Technical Support
and Updates
TC209A
HP Insight Control for Linux,
Media pack (DVD) - No licenses included NOTE: Media pack DVD contains HP
Insight Control for Linux, HP Systems Insight Manager, HP Insight Control
power management, HP Insight Control virtual machine management, and an
integrated installer. Licenses must be acquired separately.
TC208A
NOTE: Licenses
ship without media. The Media Kit for Insight Control for Linux can be ordered
separately, or can be downloaded at: http://www.hp.com/go/ic-linux
(click on Download button). NOTE: Electronic licenses can be used to purchase multiple licenses
with a single activation key, and are available in all countries except
China and Japan. Customers in China and Japan should order the physical
equivalent. NOTE: Customer will receive a license entitlement certificate, which
must be redeemed online or via fax in order to obtain the license activation
key(s). Includes one year of 24 x 7 HP Software Technical Support Service. NOTE: For additional License Kits, please see the QuickSpecs at:
http://h18000.www1.hp.com/products/quickspecs/13019_div/13019_div.html
HP iLO Advanced for BladeSystem
NOTE: Integrated
Lights-out Advanced for BladeSystem licenses may only be used for HP BladeSystem
servers
HP Integrated Lights-Out Advanced
for BladeSystem, No Media, Electronic License, including 1 year of 24x7
Technical Support and Updates
TA851AAE
HP Integrated Lights-Out Advanced
for BladeSystem, Single-Server License, including 1 year of 24x7 Technical
Support and Updates
HP Insight Control server deployment
Electronic License including 1 year of 24x7 Technical Support and Updates
T9082AAE
HP Insight Control server deployment,
Single-Server License including 1 year of 24x7 Technical Support and Updates NOTE: This license allows 1 server
to be deployed and managed via RDP. Customer will receive a printed license
entitlement certificate via physical shipment. The license entitlement certificate
must be redeemed online or via fax in order to obtain the license activation
key(s). Includes one year of 24 x 7 HP Software Technical Support Service.
452151-B21
NOTE: Licenses
ship without media. The Insight Software Media Kit can be ordered separately,
or can be downloaded at: http://www.hp.com/go/insightupdates.
NOTE: Electronic licenses can be used to purchase multiple licenses
with a single activation key, and are available in all countries except
China and Japan. Customers in China and Japan should order the physical
equivalent.
128MB Battery-Backed Cache Enabler NOTE: Supports the HP Smart Array
E200i Controller. NOTE: This option is not required when configuring a Drive-less Model.
HP 4X DDR IB Dual Port Mezzanine
HCA for HP BladeSystem c-Class
448262-B21
HP Ultrium Tape Blades
HP StorageWorks SB920c Tape Blade NOTE: LTO-3 Ultrium technology
AJ401A
HP StorageWorks Ultrium 448c Tape
Blade NOTE: LTO-2 Ultrium technology
440947-B21
NOTE: The HP PCI
Express Mezzanine Pass-Thru Card for HP BladeSystem (431643-B21) is required
when installing a tape blade adjacent to a full-height server blade. NOTE: Please see the QuickSpecs for Technical Specifications and
additional information: http://h18000.www1.hp.com/products/quickspecs/12729_div/12729_div.html
HP PCI Expansion Blade NOTE: Ships with one pre-installed
PCI-X connect board. Also includes one PCIe connect board which requires
installation. NOTE: Please see the QuickSpecs for Technical Specifications and
additional information: http://h18000.www1.hp.com/products/quickspecs/12753_div/12753_div.html
448018-B21
HP USB and SD Options
HP USB 2-Button Optical Scroll
Mouse (Carbonite/Silver)
NOTE: The HP Care
Pack service part numbers below for ProLiant BL c-Class server blades, cover
the server blade and all HP branded hardware options qualified for the server,
purchased at the same time or afterwards, internal to the server.
Hardware Services On-site Service
4-Hour On-site Service, 5-Day
x 13-Hour Coverage, 3 Years, Electronic
UK065E
4-Hour On-site Service, 7-Day
x 24-Hour Coverage, 3 Years, Electronic
UK066E
6-Hour Call to Repair, On-site
Service, 7-Day x 24-Hour Coverage, 3 Years, Electronic
NOTE:Memory
configurations listed do not apply to "Factory Integrated Models".
DIMM installation guidelines:
All DIMMs must be PC2-5300 Fully Buffered DIMMs at
667 MHz.
Both DIMM slots in a memory bank must be populated.
Banks must be populated in sequential alphabetic
order, starting with bank A.
Both DIMMs in a memory bank
must be identical. Install identical DIMMs as pairs only, starting with
DIMM socket 1, bank A.
Multiple advanced memory protection (AMP) modes
are supported, based on FBDIMM population and RBSU selection. The server
blade defaults to Advanced ECC
HP ProLiant BL460c
Server Blade (1P Model)
Standard Memory 1024 MB (2 x 512 MB) or 2048 MB (2 x
1024 MB) (depending on model)of PC2-5300, FBD DDR2-667 ECC DIMMs
Standard Memory Plus Optional Memory
Up to 50176 MB or 51200 MB (depending on model) of PC2-5300, FBD DDR2-667
ECC DIMMs. Memory is available with the installation of optional PC2-5300,
FBD DDR2-667 DIMM memory expansion kits.
Standard Memory Replaced with Optional Memory
Up to 65536 MB of PC2-5300, FBD DDR2 FBD-667 ECC DIMMs. Memory is available
with removal of standard and the installation of optional PC2-5300, FBD
DDR2-667 DIMM memory expansion kits.
NOTE: 64GB of
memory is supported with 80W processors and below. 64GB of memory is Not
supported with 120W processors. NOTE: Up to three 16 GB (2 x 8 GB) memory option kits or 48 GB of
memory is supported with 120W processors.
Hard
Drives NOTE:
The components of a storage subsystem (e.g. the drive, the HBA/controller,
firmware, and the server backplane) should operate at the same data transfer
rate or the system bandwidth will be negotiated down to an acceptable level
for all components. NOTE: Hard
drives have either a one year or three year warranty; refer to the specific
hard drive QuickSpecs for details.
SAS Hot Plug SFF (2.5-inch)
Enterprise (ENT) Drives
Quantity
Supported
Position
Supported
Controller
300GB 6G SAS 10K 300GB 3G SAS
10K DP
146GB 6G SAS 15K DP
146GB 3G SAS 15K DP
146GB 6G SAS 10K DP
146GB 3G SAS 10K DP
72GB 6G 15K DP
72GB 3G SAS 15K DP
72GB 3G SAS 10K DP
2
1-2
HP Smart Array E200i Controller
SAS Hot Plug SFF (2.5-inch) Midline
(MDL) Drives
Quantity
Supported
Position
Supported
Controller
500GB 6G 7.2K DP
2
1-2
HP Smart Array E200i Controller
SATA Hot Plug SFF (2.5-inch) Midline
(MDL) Drives
Quantity
Supported
Position
Supported
Controller
500GB 3G SATA 7.2K
160GB 3G SATA 7.2K
2
1-2
HP Smart Array E200i Controller
SATA Hot Plug SFF (2.5-inch)
Entry (ETY) Drives
Quantity
Supported
Position
Supported
Controller
250GB 3G SATA 5.4K
120GB 1.5 G SATA 5.4K
2
1-2
HP Smart Array E200i Controller
NOTE:
This option is not supported or available within the Drive-less CTO Model.
External Storage
Quantity
Supported
Position
Supported
Host Controller or Adapter
XP Disk Array Systems
Please see the XP Disk Array Systems QuickSpecs below
to determine configuration requirements
External
Please see the XP Disk Array Systems
Quick Specs for the latest list of supported HBAs
10° to 35°C (50° to 95°F) at sea level with an altitude
derating of 1.0°C per every 305 m (1.8°F per every 1000 ft) above
sea level to a maximum of 3050 m (10,000 ft), no direct sustained sunlight.
Maximum rate of change is 10°C/hr (18°F/hr). The upper limit may
be limited by the type and number of options installed.
System performance may be reduced if operating with a fan fault or above
30°C (86°F).
Non-operating
-30° to 60°C (-22°
to 140°F). Maximum rate of change is 20°C/hr (36°F/hr).
Relative Humidity
(non-condensing)
Operating
10 to 90% relative humidity (Rh),
28°C (82.4°F) maximum wet bulb temperature, non-condensing.
Non-operating
5 to 95% relative humidity (Rh),
38.7°C (101.7°F) maximum wet bulb temperature, non-condensing.
Altitude
Operating
3050 m (10,000 ft). This value
may be limited by the type and number of options installed. Maximum allowable
altitude change rate is 457 m/min (1500 ft/min).
Non-operating
9144 m (30,000 ft). Maximum allowable
altitude change rate is 457 m/min (1500 ft/min).
DDR-1/266 MHz provides up to 4.2
GB/s maximum bandwidth.
Server Interface
x4 2.5G PCIe provides 2GB/s maximum
bandwidth.
SAS Speed
x2 3G SAS provides 600MB/s maximum
bandwidth.
Cache Memory
40-bit 64 MB or 128 MB cache: ECC
protection, battery-backed, and transportable
Logical Drives Supported
Up to 32 logical volumes
Maximum Logical Drive Capacity
144GB (2 x 72GB)
Host Memory Addressing
64-bit, supporting greater than
4GB server memory space
RAID Support
RAID 5 (Distributed Data Guarding)
requires 128MB BBWC option
RAID1, 1+0 (Striping & Mirroring)
RAID 0 (Striping)
Upgradeable Firmware
Upgradeable Firmware
Embedded NC373i Multifunction Gigabit Server Adapter
Network
Processor
Broadcom 5708S
Data Transfer Method
Four
lane (x4) PCI Express
Network
Transfer Rate
2000 Mb/s full
duplex (theoretical maximum value) NOTE:
The Gigabit Ethernet adapters above transmit from the server at 2000 Mbps, full
duplex per port only. For more information, see the "Network Controller"
segment in the Standards Features section.
IEEE
Compliance
802.1p, 802.1Q, 802.3,
802.3ad, and 802.3x
Standard
Features
TCP/IP offload
engine (TOE) for Microsoft Windows 2003
iSCSI Boot for Linux
Optional
accelerated iSCSI
9K jumbo frames
TCP/IP checksum offload (TCO)
Large
send offload (LSO)
Interrupt coalescence
Dual address cycles
(DAC)
Wake-on-LAN (WOL)
Pre-boot execution environment (PXE)
ProLiant
Teaming including Network Fault Tolerance, Transmit Load Balancing, and Switch-Assisted
Load Balancing
IPv6 packet transmit and receive (excluding all offload
capabilities); IPv6 aware SNMPv1 agents for Microsoft Windows
Environment-friendly Products and Approach
End-of-life
Management and Recycling
Hewlett-Packard offers end-of-life HP product return, trade-in, and recycling
programs in many geographic areas. For trade-in information, please go to: http://www.hp.com/go/green.
To recycle your product, please go to: http://www.hp.com/go/green
or contact your nearest HP sales office. Products returned to HP will be recycled,
recovered or disposed of in a responsible manner.
The EU WEEE directive
(2002/95/EC) requires manufacturers to provide treatment information for each
product type for use by treatment facilities. This information (product disassembly
instructions) is posted on the Hewlett Packard web site at: http://www.hp.com/go/green.
These instructions may be used by recyclers and other WEEE treatment facilities
as well as HP OEM customers who integrate and re-sell HP equipment.